Straight answers on sizes, thickness, weight, grades, MTC, pricing and ordering — so your enquiry is specification-ready before you send it.
01
What is an HEAA beam?
HEAA Beams refers to a lighter HE-family variant that must not be inferred from HEA dimensions. It is used in engineered frames where a lighter HEAA profile is explicitly shown on approved documents. The name identifies a profile family, not a safe load rating; final selection must follow the approved drawing, BOQ, project standard and responsible engineer’s calculations.
02
How is HEAA different from HEA?
HEAA Beams has its own dimensional and mass series. A similar nominal depth in another family can have different flange width, thickness, radii, mass and section properties. Compare recognised section tables and approved calculations; never treat related profile names as automatic equivalents.
03
Does the live HEAA page publish a size chart?
No. The live HEAA page displays “N/A” under its size-chart heading. Buyers should therefore request the required HEAA designation, dimensional standard, complete dimensions, section properties and kg/m table at the enquiry stage, then verify them against the approved design before ordering.
04
How should a buyer request an HEAA size chart or weight table?
No. The live HEAA page displays “N/A” under its size-chart heading. Buyers should therefore request the required HEAA designation, dimensional standard, complete dimensions, section properties and kg/m table at the enquiry stage, then verify them against the approved design before ordering.
05
Can HEAA dimensions be assumed from the same nominal HEA size?
No substitution or structural selection should be made from profile name, span, flange width or unit weight alone. Capacity depends on loads, combinations, span, orientation, lateral restraint, buckling, deflection, connections, fire requirements and the design code. Any change from HEAA Beams requires revised calculations and written approval.
06
When may a lighter HEAA section be considered?
An engineer may consider HEAA Beams when its documented geometry, section properties, material grade and connection arrangement satisfy the project calculations and specification. Reduced mass, flange width or space efficiency can inform comparison, but cannot replace checks for strength, stability, deflection, buckling and fire requirements.
07
How should an HEAA beam be described in a BOQ?
State the full HEAA Beams designation, dimensional standard, material grade and grade standard, length, piece quantity or tonnage, finish, MTC, inspection and drawing reference. Depth or flange width alone is insufficient because similar headline dimensions can have different thicknesses, radii, mass and section properties.
08
Can HEAA replace HEA or HEB without recalculation?
No substitution or structural selection should be made from profile name, span, flange width or unit weight alone. Capacity depends on loads, combinations, span, orientation, lateral restraint, buckling, deflection, connections, fire requirements and the design code. Any change from HEAA Beams requires revised calculations and written approval.
09
How is the HEAA Beams price per kg calculated?
Do not publish a fixed current HEAA Beams price per kg. The rate changes with steel grade, section mass, quantity, length, finish, market date and supply route. Send the exact designation, standard, total tonnage and delivery postcode for a dated quotation, then confirm GST, freight and fabrication inclusions.
10
Can a bulk HEAA Beams supplier quote a dated tonne rate?
A current HEAA Beams price per tonne can be quoted for a defined requirement. State the exact section, material grade and standard, length, pieces or tonnage, finish, MTC, inspection and destination. Compare offers on the same weight basis and verify tax, freight, cutting, packing and documentation terms.
11
Why may two HEAA Beams supplier quotations differ?
The landed cost of HEAA Beams depends on grade, section availability, unit mass, order mix, total tonnage, length, cutting, drilling, coating, testing, inspection, packing and transport. An uncommon designation or mixed small quantities may price differently from one repetitive bulk section.
12
How is the minimum order quantity confirmed for HEAA Beams?
The live page states a minimum order quantity of 1 tonne. Confirm how MOQ applies when the enquiry mixes sections, grades, special lengths, finishes or inspection requirements. Provide the piece count and calculated tonnage for every line item so commercial feasibility can be reviewed accurately.
13
How should current HEAA Beams stock availability be checked?
Do not assume every HEAA Beams designation, grade and length is ready stock. Availability should be confirmed against the exact specification, quantity and enquiry date. If timing matters, state the required date and ask whether the quotation is based on stock, incoming material or a reviewed supply requirement.
14
Can heat traceability and an MTC be requested for HEAA Beams?
Request the MTC for HEAA Beams at the enquiry stage, stating certificate type, grade standard, heat traceability and project format. Check that the certificate matches the supplied markings, dimensions and product form. A generic document does not establish compliance with every structural, toughness or coating requirement.
15
What should third-party inspection cover for HEAA Beams?
Inspection for HEAA Beams should cover identification, dimensions, web and flange thickness, length, straightness, surface condition, quantity, marking and MTC traceability. For third-party inspection, specify the agency, stage, hold points, acceptance criteria and required reports before ordering.
16
Can fabrication drawings be included with a HEAA Beams enquiry?
Cutting, drilling or fabrication of HEAA Beams can be reviewed against an approved drawing. Provide cut lengths, hole centres, copes, notches, end plates, weld details, tolerances and piece marks. Connection design, welding procedures and any structural modification remain subject to engineer and fabricator approval.
17
Should hot-rolled or galvanised finish be stated for HEAA Beams?
The live page lists hot-rolled, galvanised or customer-specified for HEAA Beams. State the required surface condition, coating or galvanising standard, preparation, appearance and inspection. Coating suitability depends on the base material, fabrication sequence and exposure, and galvanised steel is corrosion-resistant rather than permanently rust-proof.
18
Which industries procure HEAA Beams?
HEAA Beams are considered for engineered frames where a lighter HEAA profile is explicitly shown on approved documents. Suitability depends on the exact section properties, material grade, exposure, span, restraints, loads, connections and fire requirements. Final use must follow approved calculations, drawings, BOQ and applicable project standards.
19
Does Ferrite review India-wide and export enquiries for HEAA Beams?
Ferrite can review HEAA Beams requirements for Mumbai, Navi Mumbai, Maharashtra, nearby states, India-wide supply and export enquiries. Availability and logistics depend on section and quantity. Provide the delivery postcode or destination port, Incoterm, unloading constraints and required date for review.
20
Which information prevents delay in a HEAA Beams quotation?
For a fast HEAA Beams quotation, send the profile and exact designation, dimensions, material grade, material and dimensional standards, length, pieces, tonnage, finish, make preference, MTC and inspection requirements. Add fabrication drawings, delivery postcode or port, Incoterm and required date where applicable.
